Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
In this article down the page you can locate a good deal of helpful facts about Tools You Need to Install a New Bathtub .
Installing a bathtub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably tough project. If the old bathtub is readily easily accessible, the project can move rapidly; if you have to open a wall surface to get rid of the old tub and also place the brand-new tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old tub and set in the brand-new one. Ensure you have certified yourself for the job as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is better to consider using one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will aid you install a brand-new tub in your restroom if you have currently acquired a brand-new tub and also do not need to change the plan of your previous water pipes.
Your devices as well as material list should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be quite problematic due to the restricted access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in area in between the faucet and the sink. Protect the tap in position with the supplier provided backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former type should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Making use of the two wooden boards under its feet, put the tub in the called for position. The wooden boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bath tub until the level reads level.
To set up faucets, fit the bottom of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the supply of water and also inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the tub as well as likewise examine the overflow outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the bathtub ought to wait until the bath tub has been used at least once as this will settle it into its last placement.
Getting ready for the Setup
First of all, the sustaining frame provided with the bath must be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, causing problems with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill up the tub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture relatively early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that page about How to Install a Bathtub when doing a lookup on the search engines. Appreciated our posting? Please share it. Let other people locate it. Kudos for your time. Visit us again soon.
Source This Article Report this page